asterisk.ru

Код: Выделить всё

hs1# dahdi_scan
[1]
active=yes
alarms=OK
description=Wildcard TDM410P Board 1
name=WCTDM/0
manufacturer=Digium
devicetype=Wildcard TDM410P (VPM100M)
location=PCI Bus 07 Slot 09
basechan=1
totchans=4
irq=18
type=analog
port=1,FXO
port=2,FXS
port=3,none
port=4,none

Код: Выделить всё

hs1# dahdi_cfg -vv
DAHDI Tools Version - 2.4.0-rc1

DAHDI Version: 2.4.0-rc5
Echo Canceller(s): MG2
Configuration
======================


Channel map:

Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01)
Channel 02: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 02)

2 channels to configure.

Setting echocan for channel 1 to mg2
Setting echocan for channel 2 to mg2
hs1#

Код: Выделить всё

hs1# cat /usr/local/etc/dahdi/system.conf
fxsks=1
fxoks=2

echocanceller=mg2,1-2
loadzone        = ru
defaultzone     = ru
hs1#

Код: Выделить всё

;
; DAHDI telephony
;
; Configuration file

[trunkgroups]


[channels] 
switchtype => euroisdn

language=ru
usecallerid=yes 
callwaiting=yes 
usecallingpres=yes 
callwaitingcallerid=yes 
threewaycalling=yes 
transfer=yes 
canpark=yes 
cancallforward=yes 
callreturn=yes 
echocancel=yes 
echocancelwhenbridged=no 
echotraining=yes 

group=1 
callgroup=1 
pickupgroup=1 

callprogress=yes 
progzone=us 
tonezone = 0 ; 0 is US 
jbenable = yes 

;;;[home-phones] 
context=out ; Uses the [internal] context in extensions.conf 
signalling=auto ; fxo_ks Use FXO signalling for an FXS channel - as set in sytem.conf.conf 
busydetect=yes
callprogress => yes
channel => 1 ; Telephone attached to port 1 
;dahdichan => 1 

group=2 
;;;[pstn] 
context=home ; Incoming calls go to [incoming-pstn-line] in extensions.conf 
signalling=auto ; fxs_ks Use FXS signalling for an FXO channel - use as set in system.conf 
faxdetect=incoming 
busydetect=yes 
channel => 2 
;dahdichan => 2 ; PSTN attached to port 2 

Код: Выделить всё

exten=> _7XXXXXXXXXX,1,Dial(SIP/${EXTEN}@multifon-out,30,r)
exten=> _8XXXXXXXXXX,1,Dial(SIP/${EXTEN}@sipnet,30,r)
exten=> _9XXXXXXX,1,Dial(Dahdi/1/${EXTEN:1})

Код: Выделить всё

hs1*CLI> dahdi show channels
  Chan Extension  Context         Language   MOH Interpret        Blocked    State
pseudo            default                    default                         In Service
     1            out             ru         default                         In Service
     2            home            ru         default                         In Service
hs1*CLI>

Код: Выделить всё

hs1*CLI> dahdi show version
DAHDI Version: SVN-trunk-r10321 Echo Canceller: MG2

Код: Выделить всё

hs1# dahdi_scan
[1]
active=yes
alarms=OK
description=Wildcard TDM410P Board 1
name=WCTDM/0
manufacturer=Digium
devicetype=Wildcard TDM410P (VPM100M)
location=PCI Bus 07 Slot 09
basechan=1
totchans=4
irq=18
type=analog
port=1,FXO
port=2,FXS
port=3,none
port=4,none
hs1#

Код: Выделить всё

hs1# dahdi_cfg -vv
DAHDI Tools Version - 2.4.0-rc1

DAHDI Version: 2.4.0-rc5
Echo Canceller(s): MG2
Configuration
======================


Channel map:

Channel 01: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 02)

2 channels to configure.

Changing signalling on channel 1 from FXS Kewlstart to FXO Kewlstart
DAHDI_CHANCONFIG failed on channel 1: Invalid argument (22)
Selected signaling not supported
Possible causes:
        FXO signaling is being used on a FXO interface (use a FXS signaling variant)
        RBS signaling is being used on a E1 CCS span
        Signaling is being assigned to channel 16 of an E1 CAS span
hs1#

Код: Выделить всё

hs1# dahdi_monitor 1 -v
Nothing to do with the stream(s) ...